close

How to Replace the Gear Assembly for Craftsman Snow Thrower Model 486.248381 UPDATED

How to Replace the Gear Assembly for Craftsman Snow Thrower Model 486.248381

Table of Contents: Craftsman 486.248381 Snow Blower Owner'due south Manual

35
Craftsman 486.248381 35 REPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWER

REF Function NO QTY DESCRIPTION ane 05931 i Housing, Bearing 2 65701 1 Housing Assembly 3 71464 1 Gear Assembly iv 63579 1 Chute Crank Rod Assembly five 63768 ane Impeller Assembly vi 24773 i Scraper Plate 7 25982 1 Shaft, Auger Gearbox 8 703-2735A 1 Bracket, Chute Crank nine 24816 1 Cover,Belt ten 705-5226 1 Chute Reinforcement eleven 705-5269 1 Screw Assembly, Fifty.H. (not shown) 12 705-

12
12 STEP 19: (SEE FIGURE 18) •

Attachtheclutch/idlerassemblytothetractorframe. Hook the notched pause arms onto the two shoulder bolts (Q) assembled to the outside of the tractor frame. Elevator the front of the assembly and attach information technologytotheR.H.andL.H.hangerbracketsusingtwopivot lock pins (MM) and 1/8" hairpin cotters (KK). PIVOT LOCK PIN (MM) (utilise secon

24
Craftsman 486.248381 24 INSTALLING THE ATTACHMENT PIN STEP 58: (REFER Dorsum TO

FIGURE 54 ON PAGE 23) • Liftthefrontofthesnowblowertoaligntheholesin the mounting plates and the side plates. From the left side of the tractor insert the attachment pin through the holes. Secure it with by reinstalling the ane/eight" hairpin cotter (KK). Effigy 58 SETTING THE AUGER BELT TENSION STEP 59: (Run across Effigy 57) • Pullthetensionin

28
28 RAISING AND LOWERING •

Toraise,pushdownonthelifthandleuntilthesnow thrower locks in the raised transport position. • Tolower,pushdownwardsslightlyonthelifthandleandpull the trigger. With the trigger pulled, slowly lower the snow thrower until it reaches the footing. CUSTOMER RESPONSIBILITIES • Readandfollowthema

17
Craftsman 486.248381 17 FIGURE 36 FIGURE 38 Step 36: (Encounter FIGURE 36) •

Get togetherthecablebrackettotheinnerhalfofthe double holes in the lesser of the clutch/idler assembly using 2 5/sixteen" 10 3/4" carriage bolts (O) and 5/16" nylock basics (CC). Use the front holes in the cable bracket if your tractor has a 42" mower deck. Utilize the rear holes if your tractor has a 46" mower deck. STEP 38: (Come across

23
Craftsman 486.248381 23

Note:Anadditionalperson'due southhelpmayberequiredto mount the snowfall thrower to the front end of the tractor. STEP 55: (Come across Effigy 54) • Identifythetractorandsnowthroweronaat,level surface so that the tractor tin can be rolled forward to attach the snow thrower. • RemovetheAttachmentPinfromt

half dozen
Craftsman 486.248381 vi 1. Cross Brace (Weight Tray) 2. Side Braces (2) (Weight

Tray) 3. Left Hand Side Plate iv. Right Hand Side Plate 5. Anti-rotation Bracket 6. Engagement Rod (Not used on some models) vii. Suspension Arms (2) eight. Engine Pulley Keeper (Not used on some models) 9. Chute Creepo Rod Associates 10. Support Tube, Crank Rod 11. Lift Handle and Cablevision 12. Cable Subclass 13. Plastic Keg 14. Fifty.H. Hanger Bracket (Outside Mounting) 15. R.H. Hanger Bracket (Out

15
15 INSTALLING CLUTCH/IDLER Associates

ThissectioncoverstheinstallationoftheClutch/Idler associates to tractors with attachment clutches that are either rod operated (p. 15), cable operated (p. 17) or electrical (p. 19). Use the advisable instructions for your tractor. ROD OPERATED Manual ATTACHMENT CLUTCH STEP 29: (Run into FIGURE 29) • Movementtheattachmentclutchlever

40
Craftsman 486.248381 ® Registered Trademark / TM Trademark / SM Service Mark

of Sears Brands, LLC ® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC MC Marque de commerce / MD Marque déposée de Sears Brands, LLC © Sears Brands, LLC Get information technology fixed, at your dwelling house or ours! Your Habitation For adept troubleshooting and domicile solutions advice: www.managemyhome.com For repair – in your home – of all major make applian

20
Craftsman 486.248381 twenty FIGURE 46 VIEWED FROM UNDERNEATH 1/8" HAIRPIN

COTTER (KK) ENGINE Caster ENGINE Caster KEEPER BOLT IDLER PULLEY CHAIN (PP) (L.H. SIDE) STEP 47: (SEE Effigy 46) • Get togetherthedrivebeltontotheenginepulleyand and so onto the large pulley on top of the clutch/idler assembly. The belt must exist placed to the within of the idler caster and the keeper bolt located beside the large pulley. • Place

viii
viii STEP 4: (Encounter Figure 4) • Assemble a shoulder bolt (P)

and a 3/8" washer (X) to the outside of R.H. side plate, securing it with a 3/8"angednut(BB).RepeatforL.H.sideplate. Effigy iv Right SIDE VIEW FIGURE three Correct SIDE VIEW v/16" NYLOCK NUT (CC) five/16" x 1" CARRIAGE BOLT (N) ENGINE MOUNTING PLATE (4) 1/2" WASHERS (5) (three) 3/8" FLANGE Nuts (BB) (iii) 3/8" x 1

21
21 Footstep 48: (SEE FIGURE 47) •

Placetheelevatorhandleintotheliftbracketontherightside of the snow thrower. Fasten the handle to the subclass using ii five/xvi" x 1-iii/4" hex bolts (D) and 5/16" Nylock basics (CC). FIGURE 48 Correct SIDE VIEW LIFT RELEASE Cablevision HEX NUT LOCK WASHER HEX NUT Cablevision WIRE LIFT ROD TRIGGER Associates Annotation:Besuretheli

10
Craftsman 486.248381 ten Attach CLUTCH IDLER Associates TO TRACTOR STEP 12: (SEE

Effigy 12) • Adheretheclutch/idlerassemblytothetractorframe. Hook the notched suspension arms onto the ii shoulder bolts (Q) assembled to the outside of the tractor frame. Lift the front of the associates and attach ittotheR.H.andL.H.hangerbracketsusingtwopivot lock pins (MM) and ane/8" hairpin cotters (G

iii
Craftsman 486.248381 3 Safety Any power equipment can cause injury if operated

improperly or if the user does not empathize how to operate the equipment. Practice caution at all times, when using power equipment. • Readthisowner'smanualcarefullyandknowhowto operate your snow thrower and how to stop the unit and undo the controls quickly. • Neverallowchildrentooperatetheequipment. •

19
Craftsman 486.248381 19 Electric Attachment CLUTCHES Figure 42 TENSIONING CHAIN

(PP) LEFT Forepart Hole Effigy 43 VIEW OF Bottom Footstep 43: (Run into FIGURE 43) • Hooktheleapfromthepartsbagthroughtheendof the tensioning concatenation. • Hooktheotherendofthespringontothebottomof the bolt and nut which secure the idler pulley to the upper idler arm. Hold the commodities head and assemble a 3/

27
Craftsman 486.248381 27 OPERATION KNOW YOUR SNOW THROWER Read this possessor's

manual and condom rules before operating your snowfall thrower. Comparetheillustrationbelowwithyoursnowthrowertofamiliarizeyourselfwiththevariouscontrolsandtheirlocations. CHUTE TILT HANDLEPivotstheUpperChuteupwardsor  downwards to control the bending and distance of discharge. CRANK ROD Rotates the

30
Craftsman 486.248381 30 PARTS TO REMOVE AT Cease OF Flavor •

Removetheclutch/idlerassembly.(Thetwohanger brackets and the two shoulder bolts may be left attached to the tractor frame.) • Removethedrivechugalugfromtheenginecaster. • Ifyou lotreplacedtheenginepulleykeeperonamanual attachmentclutchtractor,reinstallthetractor'soriginal engine

38
Craftsman 486.248381 38 REPAIR PARTS FOR MODEL 486.248381 42" SNOW THROWER

REF PART NO QTY DESCRIPTION 1 43080 2 Carriage Bolt, 5/xvi-18 x 3/4" two 43064 3 Hex Lock Nut, 5/16-18 three 43083 2 Hex Nut, 5/16-18 4 43086 4 Lock Washer, 5/xvi" 5 43081 4 Washer, v/xvi" Std. Wrt. half-dozen 25727 1 Frame, Clutch and Pulley 7 63904 ane Idler Arm Assembly 8 24286 ane Spacer,Pivot REF PART NO QTY DESCRIPTION nine 63762 1 Idler Bracket Associates 10 43

ix
9 3/8" X three-1/iv" HEX Commodities (B) LARGE SPACER (SS)

PULLEY (TT) 3/8" LOCKWASHER (S) iii/viii" HEX LOCK NUT (DD) 3/8" WASHER (10) LONG END OF HUB Step vii: (SEE FIGURE 7) • Attachthecaster(longendofhubfacingdown)and the large spacer (SS) to the hole shown in the clutch/ idler assembly. Use a 3/eight" 10 3-1/four" hex bolt (B), a 3/8" washer (X), a 3/viii" lock washer (S) and a

37
37 REF PART NO QTY DESCRIPTION one 64637 1 Lift Shaft Assembly

2 710-0865 two Hex Bolt, 1/two-13 10 1" 3 710-0367 2 Hex Bolt, 5/eight-eleven ten 1-ane/2" iv 711-0332 2 Pin, Bracket Elevator five 712-0261 ii Nut, Hex Lock v/8-11 Thread 6 43262 6 Nut, Hex Lock 1/2-13 8 142 5 Pin, Cotter ane/eight" x three/4" nine 43093 1 Pivot, Cotter 1/eight" x 1-1/2" ten R19171616 4 Washer, 17/32" x 1" 11 43350 vi Carriage Bolt, iii/viii-xvi x 1" 12 741-0192 2 Bearing, F

26
Craftsman 486.248381 26 CHECKLIST Earlier you operate your snow thrower, please

review the following checklist to assist ensure that yous volition obtain the all-time functioning from your snow thrower. • Brandsureallassociatesinstructionsacceptbeen completed with all bolts and nuts properly tightened. • Makesuretherightdrivebeltwasinstalled. • Makesurethedrivebeltandaugerbeltarero

ii
Craftsman 486.248381 two Table OF CONTENTS MODEL NUMBER: 486.248381 Series

NUMBER: __________________ DATE OF Buy: __________________ The model number and serial numbers will be institute on a decal attached to the snow thrower. You should record both the series number and the engagement of purchase and go along in a safe place for time to come reference. ACCESSORIES AND ATTACHMENTS Bicycle WEIGHT Theseandotheraccessoriesarerecommendedforemploywithyour

Craftsman 486.248381 Сomparable Manuals and Guides:

  • Poulan Pro 436842

    Possessor'Southward MANUALMODEL NUMBER:PP1150E27SNOW THROWER Always Habiliment Eye Protection During OperationIMPORTANT Transmission Do Non Throw Abroad Warning:Read the Owner's Manual and fol depression all Warnings and Safety In struc tions. Fail ure to do and so can issue in serious injury. 436842 Rev. i 07.xvi.10 CLPrinted in the United states of americaA. ...

    436842 Snow Blower, 44

  • Honda Automobiles HS520A

    Owner's ManualSnowthrowerHS520A HS520AS • ®© 1999–2005 American Honda Motor Co., Inc.—All Rights Reserved31V1061000X31-V10-6100IPC 5500.2005.07POM53091-CPRINTED IN U.Southward.A. EM3Printed onRecycled PaperSee page 39 for instructions onsetting up your Snowthrower.HS520K1ASHS520A ...

    HS520A Snow Blower, 62

  • Poulan Pro 424053

    OWNER'S MANUALMODEL NUMBER:PR5524ESSNOW THROWER Ever Wearable Heart Protection During OperationIMPORTANT MANUAL Practice Not Throw Away Alarm:Read the Owner's Manual and fol depression all Warnings and Safety In struc tions. Neglect ure to practice then can result in serious injury. 424053 ten.13.08 THPrinted in the The statesA. ...

    424053 Snowfall Blower, 40

  • Poulan Pro 421918

    OWNER'S MANUALMODEL NUMBER:PP1053ESSNOW THROWER Always Wear Heart Protection During OperationIMPORTANT Transmission Practise Not Throw Abroad Alarm:Read the Owner's Manual and fol low all Warnings and Safety In struc tions. Fail ure to do so tin can result in serious injury.421918 09.25.08 SR ...

    421918 Snow Blower, 40

  • Poulan Pro PP10530ES

    Possessor'Southward MANUALMODEL NUMBER:PP10530ESSNOW THROWER E'er Wearable Center Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the Possessor'southward Manual and fol low all Warnings and Safe In struc tions. Fail ure to do so can outcome in serious injury. 407885 08.03.06 BYPrinted in UsA. ...

    PP10530ES Snow Blower, 32

  • Snapper ESS5220E

    Parts Manual forRevision IR,5HP 22" SINGLE Phase SNOW THROWER(2009)TP 400-5420-IR-SX-N11/25/2008Briggs & Stratton Yard Power Products Group535 Macon Road McDonough, GA, 30253 The statesA. 800-935-2967Manual No. 7006480MODELESS5220E (1695511)SS5220E (1695470) ...

    ESS5220E Snowfall Blower, 26

  • MTD 624

    Operator'south MnualLawn TractorModel 624IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLYWarning: This unit of measurement is equipped with an internal combustion engine and should non exist used on or near whatsoever unimproved forest*covered, brush-covered or grass*covered land unless the engine'south exhaust system is equipped with a spark arrester meeting applicable loc ...

    624 Lawn Mower, 48

  • PROEL PLMN

    USER'S MANUALMANUALE UTENTEPROEL South.P.A.( WO R L D HE A D Q UA RT Eastward R South - FACT O RY)Via alla Ruenia 37/4364027 SANT'OMERO (TE) - ITALYTEL: +39 0861 81241FAX: +39 0861 887862E -thousand ail: inf o @proelgrou p. co mw due west westward. p r o east l g r o u p . c o mM Advertising E I N ITA LYCode PLMN ...

    PLMN Snow Blower, 2

  • Pulsar PTG3418

    Safety Data 53 stnetnoC egakcaP 2 four 19 24Hardware ContentsPreparation 8 9Assembly InstructionsOperating Instructions 41Care and Maintenance Parts ListingLimited Warranty81Manufactured Past:Pulsar Products, Inc.TM ...

    PTG3418 Snow Blower, xiii

  • Snapper 1696000

    Non for ReproductionParts Manual for24" 9TP 2 STAGE2011INTERMEDIATE SNOWTHROWERRevision:- half dozen/14/2011Briggs & Stratton Yard Power Products GroupManual No.7105282535 Macon Road McDonough, GA, 30253 U.S.A. 800-935-2967DescriptionModel No.1696000M924E ...

    1696000 Snowfall Blower, 28

  • Toro PowerCurve 1800

    FormNo.3424-703RevB1800PowerCurve®SnowthrowerModelNo.38381—SerialNo.319000001andUpOperator'sManualIf,aftercarefullyreadingthismanual,youstillhavequestionsorproblems,calltollfree1-800-808-2963(US)or1-800-808-3072(Canada)beforereturningthisproduct.YoumaycontactTorodirectlyatwww.Toro.comforproductandaccessoryinformation,helpndingadealer,thecompletewa ...

    PowerCurve 1800 Snow Blower, 12

  • Briggs & Stratton 120000 Quantum 675 Series

    Operating & Maintenance InstructionsBetriebsanleitung & WartungsvorschriftenDrifts- og vedligeholdelsesvejledningInstrucciones de Mantenimiento & OperaciónInstructions d'utilisation et de maintenanceÏäçãßåò Ëåéôïõñãßáò & ÓõíôÞñçóçòIstruzioni per l'uso e la manutenzioneAnvisninger for bruk og vedlikeholdGebruik ...

    120000 Quantum 675 Series Engine, 10

  • Denali VIPER MA11142

    www.motoalliance.com 1-866-527-7637 23001 Industrial Blvd, Rogers, MN 55374 / 1-866-527-7637 / www.motoalliance.com VIPER Plow SYSTEM / Can Am/Bombardier Outlander 2008-09 400/500/650/800 MA11142 Thank you lot for purchasing the premium VIPER Plow system. You at present have a top-of-the-line plow organization to using for shoving bated snow and dirt with the use of yo ...

    VIPER MA11142 Snowfall Blower, 3

  • Country Pride Snow Plough

    1© Copyright 2007 PrintedBefore You StartYour Snowfall Plow is exclusively designed for your LandPride NT & ST Treker. Please read these installationinstructions and your NT & ST Treker Operator'due south Manualthoroughly before beginning. Especially read informationrelating to rubber concerns. Also included in theOperator's Transmission is important data ...

    Snow Plow Snowfall Blower, 10

  • Poulan Pro 428510

    OWNER'South MANUALMODEL NUMBER:PR6R24SNOW THROWER Always Vesture Center Protection During OperationIMPORTANT Manual Practice Not Throw Away WARNING:Read the Possessor's Manual and fol depression all Warnings and Rubber In struc tions. Fail ure to do so can consequence in serious injury. 428510 Rev. 1 07.28.09 CLPrinted in the United states of americaA. ...

    428510 Snowfall Blower, 40

  • Yard-Man 295

    @Operator's ManuISingle StageSnow ThrowerModels 285 & 295Models E285 &E295IMPORTANT: Read safety rules and instructions advisedly earlier operating equipment.Warning: This unit of measurement is equipped with an internal combustion engine and should not exist used on or well-nigh whatsoever unimproved wood-covered, brush-covered or grass-covered land unless the engine' ...

    295 Snow Blower, 16

DOWNLOAD HERE

How to Replace the Gear Assembly for Craftsman Snow Thrower Model 486.248381 UPDATED

Posted by: kimberlyhicis1936.blogspot.com

Comments

Post a Comment